国产精自产拍久久久久久蜜,亚洲视频在线观看,亚洲小说图片,国产伦精品一区二区三区免.费

深圳市達安泰機械設備有限公司

當前位置:深圳市達安泰機械設備有限公司>>自動輸送系統>> 自動加料系統說明書

自動加料系統說明書

參  考  價:面議
具體成交價以合同協議為準

產品型號

品牌

廠商性質生產商

所在地

更新時間:2025-02-16 10:40:19瀏覽次數:65次

聯系我時,請告知來自 環保在線
自動加料系統說明書I.啟動前的準備工作1.檢查送料器的氣源壓力是否正常(0.5-0.6 MPa)以及電源是否打開; 2,檢查管件是否正確連接; 3,檢查各種材料是否準備好;II。自動加料系統說明書系統操作
自動加料系統說明書

I.啟動前的準備工作
1.檢查送料器的氣源壓力是否正常(0.5-0.6 MPa)以及電源是否打開; 2,檢查管件是否正確連接; 3,檢查各種材料是否準備好;
II。自動加料系統說明書系統操作
1.打開控制柜中的主電源開關,將控制面板上的電源旋鈕開關轉到“開"位置,電源指示燈亮;
2.在觸摸屏下校準和清,除兩個稱重系統監視器的值;
3.當觸摸屏操作進入功能選擇屏幕時,可以根據工藝要求進入“參數設置",設置“配料參數"和“時間參數"。
您還可以查看“報警記錄"和“記錄查詢"; 4,進入“操作模式"選擇“手動"或“自動",然后單擊“確認"進入操作界面; 5,如果選擇“手動",可以根據工藝要求輕觸,需要打開或關閉的機構,紅色為關閉狀態,綠色為打開狀態;設置真空給料機的控制面板。頂部的“進給"和“進給"時間可以通過“開/關"實現;
6.如果選擇“自動",則必須根據工藝要求設置“配料參數"和“時間參數"。當外部設備準備就緒時,按下控制柜上的“配料開始"按鈕,然后按“外部準備完成"按鈕。系統自動開始運行并在達到設定值后自動停止。
7.混合完成后,控制面板上的電源旋鈕開關可以在“關閉"位置關閉。一種
3.自動加料系統說明書備注
1.自動加料系統的送料時間短于送粉時的送料時間,送料時間長于送料時的送料時間。一種或者多種
2.禁止在秤上或附近焊接。 _ 一種或者多種
IV。點檢查和操作要求
1.隨時觀察系統各閥門機構的操作。一種或者多種
2.檢查供氣壓力是否正常,卸料門是否密封以及過濾器是否堵塞。一種或者多種
V.維度,護理和維護
1.定期檢查秤的精度,當秤超出公差時需要校準。在維護時應注意固定秤的運動部件。一種或者多種
3.混合后需要清潔真空供料器
Automatic feeding system manual

I. Preparation before starting
1. Check if the air supply pressure of the feeder is normal (0.5-0.6 MPa) and whether the power supply is open; 2. Check whether the pipe fittings are properly connected; 3. Check whether the various materials are ready;
II. Automatic feeding system manual system operation
1. Open the main power switch in the control cabinet, turn the power knob switch on the control panel to the “on" position, and the power indicator light is on;
2. Calibrate and clear the values of the two weighing system monitors under the touch screen;
3. When the touch screen operation enters the function selection screen, you can enter the “parameter setting" according to the process requirements, and set the “batch parameter" and “time parameter".
You can also view the “Alarm Record" and “Record Query"; 4. Enter “Operation Mode" and select “Manual" or “Auto", then click “Confirm" to enter the operation interface; 5. If you select “Manual", you can The process requires light touch, the mechanism that needs to be opened or closed, the red is off, the green is on; the vacuum feeder's control panel is set. The “feed" and “feed" times at the top can be achieved by “on/off";
6. If you select "Automatic", you must set the "Batch Parameters" and "Time Parameters" according to the process requirements. When the external device is ready, press the “Batch Start" button on the control cabinet and press the “External Ready to Complete" button. The system automatically starts running and stops automatically when the set value is reached.
7. When the mixing is complete, the power knob switch on the control panel can be turned off in the “off" position. One kind
3. Automatic feeding system manual remarks
1. The feeding time of the automatic feeding system is shorter than the feeding time when feeding, and the feeding time is longer than the feeding time when feeding. One or more
2. It is forbidden to weld on or near the scale. _ one or more
IV. Point check and operation requirements
1. Observe the operation of each valve mechanism of the system at any time. One or more
2. Check if the air supply pressure is normal, whether the discharge door is sealed and whether the filter is clogged. One or more
V. Dimensions, care and maintenance
1. Regularly check the accuracy of the scale and calibrate when the scale is out of tolerance. Pay attention to the moving parts of the fixed scale during maintenance. One or more
3. Need to clean the vacuum feeder after mixing

真空上料機聚四氟乙烯濾芯(PTFE濾蕊)

真空上料機聚四氟乙烯濾芯(PTFE濾蕊)疏水性聚四氟乙烯濾芯,其過濾介

顆粒真空上料機

顆粒真空上料機工作原理:顆粒真空上料機故障檢測及處理: 當系統檢測

真空上料機

真空上料機廣泛使用在化工,食品,注塑機、擠出機等設備的原料輸送行業中,

會員登錄

×

請輸入賬號

請輸入密碼

=

請輸驗證碼

收藏該商鋪

X
該信息已收藏!
標簽:
保存成功

(空格分隔,最多3個,單個標簽最多10個字符)

常用:

提示

X
您的留言已提交成功!我們將在第一時間回復您~

以上信息由企業自行提供,信息內容的真實性、準確性和合法性由相關企業負責,環保在線對此不承擔任何保證責任。

溫馨提示:為規避購買風險,建議您在購買產品前務必確認供應商資質及產品質量。

在線留言
主站蜘蛛池模板: 江山市| 沂源县| 句容市| 元江| 白银市| 印江| 襄垣县| 明星| 志丹县| 景洪市| 白玉县| 岐山县| 潼关县| 铁力市| 镇雄县| 客服| 青川县| 青海省| 穆棱市| 桃园县| 德惠市| 台安县| 清原| 宜良县| 庐江县| 苏尼特左旗| 小金县| 嵊州市| 成安县| 防城港市| 惠州市| 高雄市| 吉水县| 柳江县| 东乡| 东莞市| 友谊县| 惠水县| 吐鲁番市| 津南区| 贵溪市|